Injektor yang digunakan adalah injektor elektromagnet yaitu injektor yang didalamnya terdapat lilitan yang dapat menjadi magnet ketika ada arus listrik yang mengalir. Letak dari injektor pada mesin EFI dapat dilihat pada gambar dibawah ini : Kontruksi dari injektor dapat dilihat pada gambar dibawah ini : Banyak sedikitnya volume penginjeksian

After more thorough research it seems that the LB7 has two map type sensors that function as two different things. One is the boost pressure sensor that is mounted in the passenger side intake manifold, and the other is a barometric pressure sensor that is mounted externally on the driver side of the engine. From what I can tell the P0107 code

Intake Air Pressure Sensor Vixion. Baca Juga : Cara Membuat Lampu LED Motor 12 Volt. Intake Air Pressure Sensor pada Yamaha Vixion. Yamaha Vixion adalah sepeda motor sport populer yang memiliki mesin bertenaga. Seperti banyak sepeda motor modern, Yamaha Vixion dilengkapi dengan berbagai sensor termasuk Intake Air Pressure Sensor.

When I diagnosed it at first I had 3 different faulty codes: 13-Intake air pressure sensor, 30-lean angle sensor/ latch up, and 59- Throttle position sensor. So I reset them, now the check engine light is still on, but there are no faulty codes listed under D61. With the gas tank I have been putting it on and back off often to check to see if
I had surging at idle, and fault code 13, which is the air intake pressure sensor. Fortunately got it to the dealer just before warranty expired. They eventually tested that sensor and found it was bad. I was wondering if there was any mention of the problem on this forum, and found this posting.
LP,Not supported, IDE10224-MAS09684,Install. list for pressure and O2 sensors bank 1-Oxygen sensor upstrm. of oxidation cat.,supported, IDE10224-MAS09685,Install. list for pressure and O2 sensors bank 1-Oxygen sensor dwnstrm. of oxidation cat.,Not supported, IDE10224-MAS09686,Install. list for pressure and O2 sensors bank 1-Knox sensor upstrm
S6679 (AIR RIDE SEAT SUSPENSION KIT) S6691 (WATER TANK KIT / SLV75 & SLV90) S6691 (WATER TANK KIT / SLV75 & SLV90) Installation Tips & Tricks

9. Compare Inlet Manifold Pressure (IMP) value with the barometric pressure value. Are the values within 10.3 kPa (1.5 psi) of each other? a. Yes; Go to step 12. b. No; Go to step 10. 10. Disconnect the intake pressure/temperature sensor. 11. Inspect the intake pressure/temperature sensor and wiring connector for signs of damaged, bent, spread

The normal reading for absolute manifold pressure should be 14.2-15.0 psi at idle. That is the typical range of atmospheric pressure depending on elevation, temperature, etc. If it was reading manifold GAGE/BOOST pressure, it would be roughly 0 psi at idle. So, it is reading correctly. .
  • 6op8nkswjy.pages.dev/900
  • 6op8nkswjy.pages.dev/66
  • 6op8nkswjy.pages.dev/440
  • 6op8nkswjy.pages.dev/12
  • 6op8nkswjy.pages.dev/800
  • 6op8nkswjy.pages.dev/879
  • 6op8nkswjy.pages.dev/259
  • 6op8nkswjy.pages.dev/925
  • 6op8nkswjy.pages.dev/33
  • 6op8nkswjy.pages.dev/852
  • 6op8nkswjy.pages.dev/257
  • 6op8nkswjy.pages.dev/545
  • 6op8nkswjy.pages.dev/94
  • 6op8nkswjy.pages.dev/627
  • 6op8nkswjy.pages.dev/154

    • letak intake air pressure sensor vixion